3/4″ Browband Headstall #HS24
$126.00
Description: The 3/4 Inch Browband Headstall #HS24 is made of heavy single ply harness leather, 3/4 inches wide. The leather has been hand-edged, hand-rubbed, oiled with Neatsfoot Oil and hand-rubbed again. The browband is doubled and stitched which helps give this headstall a very eye-catching appearance. The throatlatch is made of 5/8 inch single ply leather. All the buckles are beveled stainless steel with leather loop keepers. The leather beneath the buckles is hand sewn together to prevent the buckles from slipping which helps make this headstall so nice to adjust to fit different horses. This is a very durable headstall that will last through years of hard use. This is the perfect headstall to ride with any bit and it’s nice enough to go anywhere and look good.
This headstall is available in 3 sizes (see dropdown). The small horse size has a 28 inch crown and is designed to fit horses under 14 1/2 hands. The average horse size has a 33 inch crown to fit horses approximately 14 1/2 to 15 1/2 hands. The large horse size comes with a 36 inch crown and is designed to fit horses over 15 1/2 hands.
Available with your choice of slot concho, concho or tie string bit ends (see dropdown).
Shown with slot conchos.
Related products
-
Two Buckle Slide Ear Headstall with Rawhide #HS53
$252.99Description: The Two Buckle Slide Ear Headstall with Braided Rawhide #HS53 is made of 5/8 inch single ply harness leather with hand-braided rawhide on the cheek pieces and a beautiful rawhide accent on the ear piece. The stainless steel buckles are beveled and have braided rawhide keepers. The leather beneath the buckles is handsewn together to keep the buckles from slipping during adjustments. This headstall looks great with the #BC5 Straight Breast Collar with Rawhide or the #BC7 Full Rawhide Braided Breast Collar and with the #CCR1 Rawhide Romel Reins.
Available with your choice of slot concho, concho, or tie string bit ends (see dropdown).
Shown with slot conchos.
Also shown on the horse is the #A4 Steel C Shank Bit with Silver, the #HU1 Bosalita 3/16 Inch, the #DMR3 Round 3/8 inch Nylon Mecate, the #CCR1 Rawhide Romel Reins and the #BC2 Shaped Breast Collar, custom stamped.
-
Sliding Gag with Link Mouthpiece #20-50
$173.99 – $213.99Description: A link mouthpiece gives this sliding gag a stronger signal than the common snaffles or the twisted wire mouthpiece and is easily accepted by horses. This Sliding Gag w/Link Mouthpiece #20-50 is made with your choice of a stainless steel twisted wire crown or, for the more sensitive horse, a 3/4 inch harness leather slide ear crown piece or a 3/4 inch brow band headstall (photo at left, please see dropdown to order).
The center bar on this bit’s cheeks limits the movement of the sliding mouthpiece to provide a quicker action and instant relief. The hard lay nylon cord allows the bit to slide easily. The cord is attached to a stainless steel buckle on each side. The buckle is attached to adjustable single ply 3/4 inch harness leather cheeks (see diagram at left). The link mouthpiece is a life-saver if your horse is resistant to the pull and does not want to follow his nose through the turn. This mouthpiece gives the strongest signals of all the gag bit choices.
How it works: The simultaneous pressure on the mouth from the sliding gag bit and on the poll from the twisted, shaped, stainless steel or the leather crown increases control of the nose and improves total balancing power to produce the ultimate in vertical flexion and feel. Because your rein aids are strengthened with the gag, your leg cues given at the same time become reinforced and easier for the horse to respond to. You will be able to better concentrate on fine details of your training rather than large rebalancing or repositioning efforts regardless of your type of riding. This gag bridle is an excellent training tool for both young and older horses that need to improve flexibility and response. Your horse will learn that when it breaks at the poll the release will be instant, smooth, and consistent. Since these gags release so quickly your horse is not trapped in position while it waits for the release to occur. This helps horses stay calm and confident in training and also when they are in competition. The leather crown is designed for horses requiring less pressure on the poll than the stainless steel twisted wire crown produces. The leather crown works well with this link mouthpiece on horses that are sensitive to pressure on the poll but very resistant to giving to the bit. There is instant relief when the pull is discontinued.
The Sliding Gag is sold without reins. Any Dennis Moreland Tack split reins or roping reins will work. To select your reins visit the rein category.
If you don’t have experience with sliding gags Dennis Moreland Tack recommends you seek the help of a professional who has experience as you are learning to use them.
-
Sliding Gag Bit with Snaffle Mouthpiece #20
$173.99 – $213.99Description: You have a choice of 3 snaffle mouthpieces and 3 headstalls with this Draw Gag Bit. The mouthpiece choices are a 3/8 inch common snaffle, a 5/8 inch common snaffle or a dog bone snaffle. See the photos at left, descriptions below, and dropdown to order. You also have your choice of 3 headstalls. The first is a stainless steel twisted wire headstall which is designed for horses that need a very strong signal. For the more sensitive horse, a 3/4 inch harness leather slide ear headstall or a 3/4 inch brow band headstall are also available. See the photo at left and the dropdown to order.
The custom designed bit slides easily on the hard lay nylon slide cord made especially for this bit. You will get quick and consistent cues from your reins because of the way the bit slides on this cord. The cord is attached to a stainless steel buckle which attaches it to adjustable single ply 3/4 inch harness leather cheeks. See the diagram at left to visualize this.
Mouthpiece choices:
#9: The Two Piece (common) Snaffle mouthpiece #9 is 3/8” in diameter. It works to give you a quicker and more consistent response when you ask your horse to give its head.
#52: The mouthpiece on the #52 common snaffle is 5/8” in diameter. The large diameter will help your horse relax. If your horse is anxious or afraid of the bit this mouthpiece may work very well. This bit gives a slower signal than a mouthpiece that’s smaller in diameter. This slower signal will help reduce anxious behavior.
#16: The 3/8” Dog Bone Snaffle. This snaffle really helps a horse relax because it is such a gentle mouthpiece. The extra link in the middle of the bit spreads the pressure from the rein signal more evenly across the mouth than a common 2 piece snaffle. The copper rings promote salivation and give the horse something to roll with his tongue to help him relax.
You may also order the Gag Bit with a twisted wire mouthpiece: #20-42 Sliding Gag w/Twisted Wire Snaffle or a link mouthpiece: #20-50 Sliding Gag w/Link Mouthpiece.
How it works: The Sliding Gag Bit puts pressure on the mouth and at the same time the headstall crown puts pressure on the poll. These 2 points of pressure increase control of the nose and improve total balancing power. With the increased control and balance you will gain vertical flexion and feel.
The draw gag bit strengthens your rein aids so your leg cues given at the same time become reinforced. This makes it easier for the horse to respond. You will be able to concentrate on fine details of your training, rather than large rebalancing or repositioning efforts. This gag bridle will improve your horse’s flexibility and increase his response to your cues.
The center bar on the bit cheeks limits the movement of the sliding mouthpiece. This limited movement provides a quicker action and a much quicker release than gags with longer shanks. Your horse learns that when it breaks at the poll the release will be instant, smooth and consistent. Your horses will be calmer and more confident in training and competition when they are not trapped by a slow releasing gag.
Choose any Dennis Moreland split reins or roping reins for your sliding gag. The Sliding Gag is sold without reins. To select your reins visit the rein category and add them to your order.
Seek the help of a professional as you are learning to use a sliding gag bit if you don’t have experience.
-
Doubled and Stitched One Buckle Headstall #HS32
$114.99Description: The Doubled and Stitched One Buckle Slide Ear Headstall #HS32 is made of 5/8 inch race track harness leather lined with oil-tanned lining leather. Race track harness is a very dense, fine grained leather which makes it strong but flexible. This is the best leather I can buy. The lining leather feels good against your horse’s face. This headstall is hand-edged, hand-rubbed, treated with Neatsfoot Oil and hand-rubbed again. The beveled buckle is stainless steel. The leather beneath the buckle is hand sewn together to prevent the buckle from slipping.
How it works: The buckle piece on this headstall is extra short to keep the buckle away from the horse’s eye. This doubled & stitched headstall is not thicker than a single ply leather headstall so has that good feel in your hands and on the horse’s face.
Crafting: To make a doubled and stitched headstall I take the race track harness and the oil-tanned lining leathers and split them to the correct thicknesses. Next I glue the 2 pieces and carefully cut the desired shapes. Finally it’s stitched together. Doubled and stitched leather is more durable and longer lasting than single ply leather and also has a nice eye-catching appearance.
The Doubled and Stitched One Buckle Slide Ear Headstall has teardrop bit ends with your choice of slot conchos, tie ends, or conchos (see dropdown).
Shown with slot conchos.
-
Bridle with 3/8″ Snaffle & Doubled & Stitched Reins #HT4
$368.99The Bridle with 3/8″ Snaffle & Doubled & Stitched Reins is the perfect bridle to ride your colts in. It’s is made up of the:
• Headstall: 3/4 inch Browband Headstall #HS25. This headstall is made of heavy 3/4″ wide single ply harness leather. The leather has been hand-edged, hand-rubbed, oiled with Neatsfoot Oil and hand-rubbed again. The browband is doubled and stitched. The throatlatch is made of 5/8 inch single ply leather. All the buckles are beveled stainless steel with leather loop keepers. The leather beneath the buckles is hand sewn together to prevent the buckles from slipping which makes this headstall easily adjustable between horses. This bridle is available in 2 headstall sizes (see dropdown). The average horse size has a 33″ crown to fit horses 15 hands and under and the large horse size comes with a 36″ crown and is designed to fit horses over 15 hands. The short cheek pieces on this headstall keep the buckles away from the horse’s eyes.
• Bit: 5/16″ Ring Snaffle #17 with the #9 3/8″ mouthpiece. The mouthpiece on this snaffle has a slight bow which tends to be easier on the mouth while at the same time giving a stronger signal than a flat mouthpiece. The mouthpiece is inlaid with copper to promote moistness in the mouth. Close-up of the bit shown at left.
• Curb: Leather Curb Strap with Rawhide #CU40. This curb is made of 1/2 inch hand-edged latigo and is complimented with beautiful hand braided rawhide balls and loops. This curb is AQHA and NRCHA legal.
• Reins: Latigo on Latigo 5/8″ Reins Med Wt #BLL1 or Latigo on Latigo 5/8″ Reins Heavy Wt #BLL2. Your choice of medium or heavy weight Doubled and Stitched Reins (see dropdown) are made particularly for ranch sorting and other work that requires the horse to stay collected. At 7 feet in length they are perfect for keeping your horse gathered in those quick tight turns while not dragging the ground. They are just right for riding colts and our shorter cutting and cow horses too. Close-up of the reins shown at left.
This bridle is designed for the Cutter, Ranch Sorter and Cow horse. It’s very functional and built to last. Best of all it will help you in those quick tight turns in the pen! This is also the perfect piece of equipment to start your colts in.
